Evaluation and Optimization of Synthesized Silica Nanocomposite for Degradation of Methylene Blue Dye Using Response Surface Methodology

Effective wastewater treatment for synthetic dyes is crucial for environmental sustainability attributed to the toxic nature and persistence of these pollutants. Methylene blue (MB), a widely used synthetic dye that can contribute to severe environmental concern if not properly removed from wastewater. Nanomaterials have emerged as highly efficient agents for degrading MB offering a promising solution for wastewater treatment. NaCl-SiO2 NCs were synthesized through the sol-gel method. The successful formation of the composite was also confirmed by characterization results, with X-ray Diffraction (XRD) patterns showing the presence of a combination of crystalline NaCl and amorphous SiO2 phases and Fourier Transform Infrared (FTIR) spectroscopy showing the presence of key functional groups, silanols (Si-OH) at 1043 cm-1 and Si-O-Si at 796 cm-1, which are crucial to dye adsorption. The degradation of MB in aqueous solution was used in these nanocomposites. Response Surface Methodology (RSM) was used to optimize processes through a Central Composite Design (CCD) to assess the effect of nanocomposites dose, contact time, and pH. Optimal conditions were considered to be the highest percentage (97.2%) of MB degradation at a nanocomposite dose of 100 mg/50 mL, pH 6, and a contact time of 140 minutes. This suggests that NaCl-SiO2 nanocomposites are a good, eco-friendly substance that can be used to effectively degrade dye in wastewater treatment and has a high possibility of large-scale applications.read more


Samina Gull, Naeem Abbas, Mohsin Raza, Najma Ameer Mian Habib-ur-Rehman Mahmood and Muhammad Hammad Khan

Investigating Residual Solvents and Barrier Efficiency in Food Packaging: Implications for Regulatory Compliance

Food packaging is necessary for ensuring the quality and safety of food. However, production materials can migrate from packages to packaged foods if they contain residual solvents due to ink printing by-products that may have deteriorated into components with risks to human health after a certain period in time during storage. The objectives of this work were to (1) quantify prohibited and restricted residual solvents (methanol, ethylene glycol, and toluene) in flexible potato chip packaging by using validated gas chromatography; (2) determine water vapor permeability qualities with permeation analyzers;(3) evaluate safer solvent substitutes through Hansen Solubility Parameters; (4) compare environmental impacts utilizing life cycle assessment. Five individual samples of locally-available local leaders and imports were examined. Local brands had significantly higher levels of residue solvents (methanol: 0.042–0.268 mg/m2; ethylene glycol: 0.263–1.247 mg/m2 toluene: 0.012–0.792) than imported and leading brands. The properties of each barrier varied significantly, with Sample D additionally showing the lowest WVTR at (0.14 g/m²/day) and sample B had a low O₂ transmission rate at (3.58 cm3/m2/day) respectively but it is much bigger than one can be bearable if not controlled timely by near field imaging [ref]. Four less hazardous substitutes were pinpointed through Hansen solubility parameters: ethanol for methanol, propylene glycol monomethyl ether acetate (also known as 1-methoxypropyl acetate or PGMEA) to replace ethylene glycol and a n-propyl alcohol/n-propyl acetate mixture stood in lieu of toluene. Most items had lower environmental impacts for leading brands and imports, LCA found. These results highlight the importance of strict Good Manufacturing Practices, implementation of high barrier films, solvent displacement and unified national laws in Pakistan. It presents a global architecture that links local practice to international standards on safety and sustainability.read more


Mahnoor Mujeeb, Saad Nadeem and Shan Ali

Pt/CNTs Co-Modified Tubular g-C3N4 for Highly Efficient Visible-Light-Driven Photodegradation of Rhodamine B

Developing photocatalysts with multidimensional conductive networks and synergistic interfaces is a promising strategy to suppress charge carrier recombination and enhance visible-light-driven photocatalytic performance. Herein, a Pt and carbon nanotube (CNT) co-modified tubular g-C3N4 photocatalyst (Pt/CNT@g-C3N4) was successfully fabricated via an electrostatic self-assembly strategy. The introduction of CNTs constructed efficient electron transport pathways, while highly dispersed Pt nanoparticles formed stable metal–semiconductor interfaces. Their synergistic coupling broadened visible-light absorption, narrowed the bandgap, and promoted the separation and migration of photogenerated charge carriers. At the optimal composition (2 wt% Pt and 1.5 wt% CNTs), Pt/CNT@g-C3N4 exhibited a Rhodamine B (RhB) degradation rate constant of 0.148 min⁻¹, which was approximately 10.8 times higher than that of pristine tubular g-C3N4, achieving 96% pollutant removal within 20 min under simulated visible-light irradiation. In addition, the catalyst retained over 83% of its initial photocatalytic activity after five consecutive cycles, indicating good stability and reusability. Radical trapping experiments combined with electron paramagnetic resonance (EPR) measurements confirmed that ·O₂⁻ radicals were the dominant reactive species during the photocatalytic process. Moreover, the enhanced photocatalytic performance was mainly attributed to the efficient extraction and transfer of photogenerated electrons from g-C3N4 through two synergistic pathways mediated by Pt nanoparticles and CNTs, which effectively suppressed electron–hole recombination. This work reveals the synergistic enhancement mechanism of Pt and CNTs in tubular g-C3N4 systems and provides a rational strategy for designing efficient visible-light-driven photocatalysts for environmental purification.read more


Junkai Wang, Jinsheng Kang, Zhenxia Huang and Jingyi Xing

The Search for a Cracking Catalyst: Aluminum- and Surfactant-Modified ZSM-5 Zeolites

In the present study, modified ZSM-5 catalysts were synthesized, characterized, and tested for their cracking activity and selectivity toward desired cracked products. The ZSM-5 zeolite was modified by aluminum impregnation to increase the acidic strength as well as by non-ionic Pluronic F127 surfactant to induce the mesoporosity in the zeolitic structure. The catalysts were characterized and their catalytic performance was evaluated in a high-pressure Parr autoclave reactor through n-hexadecane cracking. The experiments were performed at a fixed residence time of 60 min, a feed-to-catalyst ratio of 20:1 by weight, different cracking temperatures between 325°C and 400°C, and an initial cold pressure of 1 bar. The reaction products (both gas and liquid) were quantitatively analyzed by a GC-FID system. The results of the cracking experiments showed that at 350°C, the 2.5 wt% aluminum-impregnated ZSM-5 catalyst offered significantly high conversion (79.1%) and selectivity toward gasoline-ranged hydrocarbons compared to the other aluminum-modified catalysts. The modification with F127 considerably reduced the crystallinity of ZSM-5 and resulted in relatively higher conversions but lower liquid yields.read more


Abdullah Ramzan and Muhammad R Usman

Fabrication and Characterization of Graphene Oxide for Biomedical Applications

Graphene Oxide (GO) has garnered significant attention for its potential in biomedical applications, including wound healing, drug delivery, biosensing, cancer therapy and environmental sustainability. However, the costly fabrication and characterization methods have hindered its utilization in these applications, especially in developing countries like Pakistan, where financial and resource constraints limit access to advanced materials like GO. In this study, high-quality Graphene Oxide is successfully fabricated using a cost-effective approach utilizing modified Hummer’s method adapted to resource constrained laboratory conditions, offering a cost effective and scalable alternative. The synthesized GO was comprehensively characterized using FTIR, SEM, XRD, TGA, and DSC. XRD confirmed a well-ordered layered structure with characteristic peak at 10.9° (d-spacing = 8.7 Å), indicative of successful oxidation. FTIR identified key oxygenated functional groups; hydroxyl, epoxy, carbonyl and carboxyl, essential for biomedical functionality. SEM revealed a uniform particle size of approximately 10 μm, with porous regions that may enhance adsorption performance. Thermal analysis (TGA\ DSC) confirmed the presence of oxygen containing groups, validating the degree of oxidation. The promising results demonstrate that the proposed approach produces GO with properties consistent with established literature, while significantly reducing fabrication barriers. This research lays a foundation for affordable GO based solutions in wound healing, targeted drug delivery, biosensing and environmental remediation in developing countries.read more


Amna Amin Sethi, Hoorain Sajjad, Ramna Ayub, Bisma Arif, Romesa Arshad and Eraj Humayun Mirza

Ultrasound Assisted Extraction of Lavender Essential Oil and its Potential Applications in Perfumery

Lavender essential oil was well known for its pleasant scent and wide range of uses in the fragrance business. This study contrasted traditional steam distillation with ultrasound-assisted extraction (UAE), an alternate method for extracting lavender essential oil. The extracted oil's chemical makeup, antioxidant activity, antibacterial qualities, extraction yield, and potential for perfume formulation were all examined. UAE outperformed steam distillation in terms of extraction yield at the experimental conditions used. According to GC-MS analysis, the most common volatile chemicals found in the extracted oil were camphor (21.18%), α-thujene (16.27%), and endo-borneol (14.05%). When tested against the bacteria, the lavender essential oil shown significant antimicrobial and antioxidant action. During hedonic evaluation, perfume compositions made with the extracted oil showed acceptable sensory qualities. Under the conditions examined, UAE needed less time for extraction and less solvent than steam distillation. According to the results, ultrasound-assisted extraction may be a viable substitute method for extracting lavender essential oil and using it in perfumery. It was suggested that more research be done to assess its environmental performance and large-scale usability.read more


Hafiza Rimsha Afzal, Muhammad Suleman and Freeha Hafeez

Study of The Interaction of A Zinc (II) Phthalocyanine Complex with a 2,4-Di-Tert-Butylphenoxy Substitute with Calf Thymus DNA

Zinc (II) phthalocyanine complex was previously obtained from the compound of 4-(2,4-di-tert-butylphenoxy)phthalonitrile and characterized by spectroscopic methods like elemental analyses, absorption, NMR and infrared spectra. In this research conducted, the interaction properties of Zn(II) phthalocyanine compound containing 4-(2,4-di-tert-butylphenoxy) substitute by calf thymus DNA (CT-DNA) were investigated by absorption titration, fluorescence, viscosity, gel electrophoresis and melting temperature methods. The Kb value for this complex was found to be 2.58 (± 0.32) x106 M-1. The Kb value supports that the complex binds to base pairs of DNA through intercalative bonding mechanism. The data obtained from fluorescence, viscosity and melting temperature studies were confirmed by the data obtained from absorption titration. In addition to the above methods, a gel electrophoresis study was also performed and this technique confirmed that the complex interacts with DNA. In the light of these data, Pc-Zn compound can be considered as a potential drug after further research on the complex.read more


Ali Arslantas and Mehmet S. Agirtas

Biochemical Extraction and Optimization of Cellulose Fibers from Reeds for Sustainable Applications

This study presents an optimized biochemical process for extracting cellulose fibers from reed biomass (Phragmites australis) as a sustainable alternative to synthetic materials. A modified organosolv delignification method was developed and optimized using Response Surface Methodology (RSM) with Central Composite Design (CCD) to evaluate the effects of temperature (120–200 °C), ethanol–water ratio (50–70 wt%), and digestion time (1–3 h) on lignin removal. Optimal conditions (160 °C, 60:40 ethanol–water, 3 h) resulted in residual lignin content of 3% (R² = 0.9895), experimentally validated with minimal prediction error. Catalytic enhancement with low-concentration sodium hydroxide (0.025 M) further reduced lignin to 0.51% in just 2 h, significantly improving efficiency without compromising cellulose integrity. Comprehensive physicochemical, morphological, and thermal characterizations confirmed that the extracted fibers are suitable for high-value applications in textiles, bio-composites, and bio-based materials. The developed process demonstrates scalability, reduced chemical and energy consumption, and potential integration into circular bioeconomy pathways, which ultimately support the sustainable development of communitiesread more


Yasmeen. S. Mahdi and Rawa G. Yousuf